GIGAWARE USB TO ETHERNET MAC DRIVER INSTALL
GIGAWARE USB TO ETHERNET MAC DRIVER DRIVERS
GIGAWARE USB TO ETHERNET MAC DRIVER UPDATE
GIGAWARE USB TO ETHERNET MAC DRIVER DRIVER

I was not sure if the device I had purchased no longer worked or if was the drivers? I saw that these modules were initially compiled for ESXi 5.1 (at the time, that was the latest version) and the only difference was that I was using a much newer version of ESXi, specifically 6.0 Update 1. Vmkwarning.log:T21:54:54.531Z cpu6:374787)WARNING: Elf: 2041: Load of failed : missing required namespace Īs you can imagine, I was pretty bummed to see this since I was afraid that something like this would happen. When I tried to initially load either of the modules, I would always get the following error: Vmkload_mod /vmfs/volumes/mini-local-datastore-1/ax88179vz026 Vmkload_mod /vmfs/volumes/mini-local-datastore-1/usbnetvz026 Here are the two commands that I used in the following order: I have included the links below for your convenience:Īs the VMTN thread mentioned, you can load using either the vmkload_mod or ESXCLI. There are two modules that needs to be downloaded, extracted and loaded onto ESXi. I decided to bite the bullet and give this solution a try and purchased the USB ethernet adapter from Amazon here.

The following solution is not officially supported by VMware, please use at your own risk.

GIGAWARE USB TO ETHERNET MAC DRIVER INSTALL

UPDATE (03/29/16) - Please have a look at this updated article here which includes ESXi 5.5 and 6.0 driver.ĭisclaimer: In case it is not clear and apparent, you should never install any unknown 3rd party software on your ESXi host as it can potentially lead to instability issues or worse open yourself to a security hole.

GIGAWARE USB TO ETHERNET MAC DRIVER DRIVER

If you are still on ESXi 5.5/6.0, you can continue using the existing driver but please note there will be no additional development in the existing vmklinux-based driver. UPDATE (02/12/19) - A new VMware Native Driver for USB-based NICs has just been released for ESXi 6.5/6.7, please use this driver going forward. It was only until last week, I decided to start fresh again and after a bit of Googling I came across an old VMTN thread here where VMTN user AK_28 mentioned he had success with the StarTech USB 3.0 to Gigabit Ethernet NIC Network Adapter and using a custom compiled driver that was posted over here by another user named Trickstarter.

GIGAWARE USB TO ETHERNET MAC DRIVER DRIVERS

One option that has been suggested by many folks over the years was to see if a USB based ethernet adapter could be used to provide additional networking to ESXi? Historically, the answer had been no because there were no known device drivers that would work with ESXi. I had even looked into this a few years ago and although I ran into some folks who seemed to have made it work, I was never able to find the right USB ethernet adapter to personally confirm myself. Perhaps, with the next update of the NUC platform code named 'Skull Canyon', the rumored Thunderbolt 3 / USB-c connector may make things easier as some of the existing vendors who produce Thunderbolt to ethernet adapter also use common drivers like the Broadcom tg3 which have historically worked with ESXi.

However, the NUC also lacks additional IO connectors like a Thunderbolt port which the Mac Mini includes and can support a Thunderbolt to Ethernet adapter. I think this is probably the only downside to the Intel NUC platform which has been similar feedback that I have seen from other vSphere home labbers who currently use or would like to use the NUC. The Intel NUC only includes a single built-in ethernet adapter which is similar to the Mac Mini. As part of upgrading my personal vSphere home lab from an Apple Mac Mini to an Intel NUC (more on this in a future blog), I have been researching to see if there are other alternatives for adding an additional network adapter.

Gigaware usb to ethernet mac driver